Вид ABC пластика: Импортный
Метод переработки ABC пластика: Литье
Производители: Styrolution Group GmbH

Luran® 368 R Crystal Clear

Product description:

General-purpose grade with well-balanced properties, suitable for injection moulding and extrusion.Especially for
applications where highest transparency and low natural colour is required.

Physical form and storage:

Luran® is supplied as cylindrical or lenticular pellets. The bulk density is approx. 0.55-0.65 g/cm³.
Standard pack: 25 kg PE sack, palletized and film-secured. PE bags should not be stored outside. Subject to agreement,
other means of packing are possible, e.g. 1000 kg bulk containers (flexible IBCs or intermediate bulk big bag containers);
shipping by road tanker can be arranged. Luran® pellets can be stored for prolonged periods in dry areas subject to
normal temperature control without any changes in mechanical properties. However, for sensitive colors storage over
some years can cause some color change. Under poor storage conditions, Luran absorbs moisture, which can be
removed again by drying. Packs stored in cold areas should be brought to ambient temperature before opening, to prevent
condensation on the pellets.

Product safety:

Given appropriate processing of the products and suitable ventilation measures in production areas, no adverse effects on
the health of process operators have been found. Workplace limits for styrene, alpha-methylstyrene and acrylonitrile, as
given in the national listings applicable, must be adhered to.
The values currently applicable in Germany under TRGS 900 (issue of October, 2002) for maximum workplace
concentrations are as follows. Styrene: 20 ml/m³ = 86 mg/m³; alpha-methylstyrene: 100 ml/m³ = 480 mg/m³; acrylonitrile: 3
ml/m³ = 7 mg/m³. Appendix I of Directive 67/548/EWG and TRGS 905 (issue of October,2002) classify acrylonitrile in
carcinogenic category II (substances which should be regarded as carcinogenic in humans).
Experience has shown that during appropriate processing of Luran with suitable ventilation the values obtained are well
below the limits mentioned above. TRGS 402 (Germany) can be used for determining and assessing the concentrations of
hazardous substances in the air within working areas.
Inhalation of gaseous degradation products, such as those which may arise on severe overheating of the material or
during pumped evacuation, must be avoided. Further information can be found in our Luran safety data sheets. These can
be downloaded from the Plastics Portal, www.plasticsportal.net.

Note:

The data contained in this publication are based on our current knowledge and experience. In view of the many factors
that may affect processing and application of our product, these data do not relieve processors from carrying out their own
investigations and tests; neither do these data imply any guarantee of certain properties, nor the suitability of the product
for a specific purpose. Any descriptions, drawings, photographs, data, proportions, weights etc. given herein may change
without prior information and do not constitute the agreed contractual quality of the product. It is the responsibility of the
recipient of our products to ensure that any proprietary rights and existing laws and legislation are observed.
In order to check the availability of products please contact us or our sales agency.

Typical values for uncoloured product at 23 °C1) Standard Unit Values
Properties      
Polymer abbreviation - - SAN
Density ISO 1183 kg/m³ 1080
Moisture absorption, equilibrium 23°C/50% r.h. similar to ISO 62 % 0.2
Processing      
Method: Injection moulding (M), Extrusion (E) - - M. E.
Melt volume-flow rate MVR 220 °C/10 kg ISO 1133 cm³/10min 10
Melt volume-flow rate MVR 200 °C/21.6 kg ISO 1133 cm³/10min 12
Pre-drying: Temperature - °C 80
Pre-drying: Time - h 2-4
Melt temperature, injection moulding - °C 220-280
Mould temperture, injection moulding - °C 40-80
Melt temperature, extrusion prepreg - °C 220-240
Melt temperature, extrusion plates - °C 220-240
Melt temperature, extrusion pipes - °C 220-240
Melt temperature, extrusion profiles - °C 240
Moulding shrinkage, free, longitudinal - % 0.3-0.7
Flammabillity      
UL94 rating at 1.6 mm thickness UL-94 class HB
UL94 rating at 0.8 mm thickness UL-94 class HB
Mechanical properties      
Tensile modulus ISO 527-1/-2 MPa 3700
Stress at break ISO 527-1/-2 MPa 76
Strain at break ISO 527-1/-2 % 3
Flexural strength ISO 178 MPa 126
Tensile creep modulus, 1000 h, strain <= 0.5%, 23°C ISO 899-1 MPa 2800
Charpy unnotched impact strength (23°C) ISO 179/1eU kJ/m² 18
Izod notched impact strength, 1A (23°C) ISO 180/A kJ/m² 2
Charpy notched impact strength (23°C) ISO 179/1eU kJ/m² 2
Ball indentation hardness at 358 N/30 s ISO 2039-1 MPa 186
Rockwell hardness ISO 2039-2 class M83
Thermal properties      
HDT A (1.80 MPa) ISO 75-1/-2 °C 88
HDT B (0.45 MPa) ISO 75-1/-2 °C 100
Vicat softening temperature VST B50 ISO 306 °C 108
Max. service temperature (short cycle operation) - °C 86
Coefficient of linear thermal expansion, longitudinal (23-80)°C ISO 11359-1/-2 E-4/°C 0.7
Thermal conductivity DIN 52612-1 W/(m K) 0.17
Electrical properties      
Relative permittivity (100Hz) IEC 60250 - 3
Relative permittivity (1 MHz) IEC 60250 - 2.7
Dissipation factor (100 Hz) IEC 60250 E-4 40
Dissipation factor (1 MHz) IEC 60250 E-4 70
Volume resistivity IEC 60093 Ohm*m 1E14
Surface resistivity IEC 60093 Ohm >1E15
Electric strength K20/P50, d = 1 mm IEC 60243-1 kV/mm 34

Хотите купить ABC пластик АБС Luran 368 R?

Позвоните нам по телефону +7 (831) 214 33-00, мы расскажем вам о наличии, стоимости и сроках поставки ABC пластик.

Так же вы можете связаться с нашими менеджерами по электронной почте: Адрес электронной почты защищен от спам-ботов. Для просмотра адреса в вашем браузере должен быть включен Javascript.

Звоните, мы всегда готовы к долговременному сотрудничеству по поставке полимерного сырья любой марки.